All guides

US versionOther versions: France (in French) · Belgium (in French) · Switzerland (in French) · England

Air Conditioning and Heat Pumps

What size air conditioner does your room need?

The right capacity matters more than the biggest number on the box.

The answer in 2 lines. For a window or through-the-wall room AC, start with the federal ENERGY STAR sizing chart, which matches floor area in square feet to cooling capacity in BTU per hour. Adjust for conditions such as strong sunshine and regular occupancy. For a mini-split or whole-home system, ask for a documented load calculation. An oversized AC can cool quickly while leaving the room damp.

The first 3 steps

  1. Measure the room's length and width in feet, multiply them, and note the ceiling height.
  2. Record direct sun, window exposure, insulation concerns, regular occupants and whether the space includes a kitchen.
  3. Identify the equipment category: a room-AC chart is a starting point for room equipment, not a complete mini-split design.

Stop: danger

  • Electrical supply: selecting a cooling capacity does not establish that your outlet or circuit can run the equipment safely. Check its electrical requirements before purchase.
  • Window installation: do not install equipment that cannot be securely supported or would block an emergency exit.

A starting chart for room ACs

The ENERGY STAR room-AC guide provides a sizing table. Measure your floor area, find the matching row, then apply the adjustments below. These are technical recommendations available in 2026, not annual sales figures; the chart assumes an 8-foot ceiling.

Area to coolStarting capacity
100 up to 150 square feet5,000 BTU/h
150 up to 250 square feet6,000 BTU/h
250 up to 300 square feet7,000 BTU/h
300 up to 350 square feet8,000 BTU/h
350 up to 400 square feet9,000 BTU/h
400 up to 450 square feet10,000 BTU/h

Use the full linked table for other sizes. Higher ceilings or unusual construction need additional assessment.

What not to do

  • Buying extra capacity simply to be safe: oversizing can reduce efficiency and humidity removal.
  • Treating electrical watts as the cooling output.
  • Using the total apartment area when you will actually cool a closed bedroom.
  • Assuming a single indoor unit will cool separate rooms evenly through narrow doorways.

Adjust for the room you actually have

In its current guidance consulted in 2026, ENERGY STAR recommends reducing the chart capacity by 10% for heavy shade or increasing it by 10% for a very sunny room. Add 600 BTU/h for each regular occupant beyond two, and 4,000 BTU/h for a kitchen.

These adjustments help you screen room units. They do not account fully for an attic room, extensive glazing, unusual ceiling heights or a complicated floor plan. Bring those details to the installer rather than stacking guesses onto the chart.

For portable equipment, compare the same rating method across your shortlist. The DOE portable-AC document explains SACC, the seasonally adjusted cooling-capacity metric. Check that the advertised number you use is the DOE-rated figure.

For a mini-split, ask what supports the proposal

A permanent system should be selected around the building's cooling and heating loads, its layout and the equipment's operating range. Ask for a written explanation of the room-by-room assessment, proposed indoor-unit locations and how the system will serve rooms with doors closed.

The federal Building America mini-split guide explains design and installation considerations. Use its sizing and installation sections to prepare questions for your contractor. If heating is part of the project, ask how winter conditions affect the selection.

Permits and contractor licensing vary by state and locality. Use the USAGov directory to reach your local building department and ask what approvals apply before work begins.

Good to know

  • A cold but clammy room can indicate poor humidity control; lowering the thermostat further is not necessarily the solution.
  • Compare proposals that describe the same rooms, comfort goals and included installation work.
  • Ask about the equipment's lowest operating capacity as well as its maximum output, especially for a small room.

Illustrative example: a homeowner wants to cool a sunny upstairs bedroom. She measures the room, checks the official chart and notes the roof exposure and high ceiling. Instead of buying the largest available unit, she asks whether a room AC is suitable and requests a load assessment before considering a permanent mini-split.

A made-up story, for illustration.

Bobby

Read more guides

Bobby publishes free practical guides written for the United States: American laws, numbers and organizations. In the United States, Bobby answers your questions; it does not put you in touch with professionals.

All guides: United States

Sources, verification, confidence

Verified on November 7, 2026, for the United States. Confidence: high for the published room-AC chart, its adjustments and the risks of oversizing; medium for applying a starting estimate to unusual rooms. The figures are technical guidance consulted in 2026, not a substitute for an installation calculation.

Related guides

Also worth reading