All guides

US versionOther versions: France (in French) · Belgium (in French) · Switzerland (in French) · England

Clothes dryers

Is your dryer damaging clothes? Shrinking, pilling and snags

Start with the clothing label before blaming the dryer.

The answer in 2 lines. A dryer can damage clothing when the garment is unsuitable for tumble drying or the settings are inappropriate. Read the care label before another attempt. Shrinking, attached fiber balls, loose lint and tears are different problems. Photograph the damage and check whether it was already present after washing. If multiple items develop similar snags, or you see a damaged drum surface, stop using the dryer and arrange an inspection.

Start here

  1. Set the damaged item aside. Photograph the whole garment, the affected area and its care label before stretching, trimming or washing it again.
  2. Write down the wash and dryer settings you used, including heat and dryness level. Check whether other items from the same load have similar damage.
  3. With the dryer stopped, cooled and unplugged, inspect only the visible drum and doorway. Remove loose objects you can reach easily; leave anything trapped behind a component.

Stop: danger

  • Repeated tears or a visibly damaged interior: stop using the dryer until a qualified appliance repair professional checks it. Do not reach along a sharp edge or run another load to test it.
  • Burning odor, smoke or a damaged electrical connection: stop use. Disconnect power only if you can do so safely. If there is fire or spreading smoke, leave the home and call emergency services from outside.

Read the drying instruction, not just the fiber content

Most covered clothing sold in the US must carry care instructions under the federal care-labeling rule, although exceptions exist. Cotton, wool or polyester on the composition label does not tell you everything about a finished garment. Its construction, lining, trim and finish can affect the appropriate care.

Use the care-symbol chart hosted by the FTC: find the Dry section and match the complete symbol, including dots, underlining and any cross. US symbols distinguish low, medium and high heat. A crossed-out tumble-dry symbol means do not tumble dry; dry flat means support the garment horizontally. Then use your appliance manual to identify the compatible setting.

What not to do

  • Using low heat or a delicate cycle when the garment says not to tumble dry.
  • Choosing a setting for the toughest item in a mixed load and exposing delicate pieces to the same treatment.
  • Running already-dry clothing through repeated heated cycles to improve its appearance.
  • Pulling loose threads, aggressively stretching a shrunken garment or treating an online unshrinking recipe as a guaranteed fix.
  • Assuming lint collected in the filter proves that the dryer caused a particular tear or amount of wear.

Separate the problems before trying a fix

  • Shrinking: compare every washing and drying instruction with what actually happened. Set aside a valuable garment for advice from a textile-care professional before another treatment.
  • Pilling: describe the small balls that remain attached to the fabric. Their appearance after drying does not establish which stage of wear or laundering caused them.
  • Loose lint: check whether fibers rest on the surface rather than forming attached balls. Avoid pulling at the fabric to find out.
  • Snags or tears: note their position and whether the pattern repeats across unrelated garments. Keep damaged pieces available for inspection.

If the care label is missing or unreadable, ask the seller for the garment's instructions. Until you have them, avoid experimenting with heated drying. Hanging is not automatically suitable either: some garments need flat drying.

Prevent the next damaged load

Sort by compatible care instructions and drying needs. Empty pockets and inspect clothing before washing and again before drying, so you can identify when a new defect appears. Follow the program-specific loading instructions rather than assuming every cycle accepts the machine's maximum load.

Keep maintenance separate from garment treatment. Follow the U.S. Fire Administration dryer checklist: use it to check lint-filter cleaning and vent maintenance, and have the appliance serviced professionally when needed. A clean filter does not make an unsuitable garment safe to tumble dry.

If damage occurs despite following the instructions, retain the receipt, photos and label. Explain the facts to the clothing seller or appliance service provider without claiming a cause that has not been established.

Good to know

  • The cycle name alone is insufficient: both the garment instructions and the machine settings must be compatible.
  • No universal dryer-caused shrinkage percentage or pilling rate is used here. An individual garment and its care history need assessment.
  • There is no confirmed universal treatment that restores every shrunken garment to its original dimensions.

Illustrative example: Jordan notices that a sweater looks smaller after drying. The machine was on a gentle setting, but the garment label says dry flat. Jordan photographs the label, sets the sweater aside and asks a textile-care professional for advice. Before the next load, Jordan separates garments by drying instructions instead of relying on the cycle name.

A made-up story, for illustration.

Bobby

Read more guides

Bobby publishes free practical guides written for the United States: American laws, numbers and organizations. In the United States, Bobby answers your questions; it does not put you in touch with professionals.

All guides: United States

Sources, verification, confidence

Verified on November 14, 2026, for the United States. Confidence: high for US care-label instructions and dryer maintenance precautions; medium for practical troubleshooting. The cause of damage and the prospects of restoring a garment cannot be confirmed remotely.

Related guides

Also worth reading