All guides

England versionOther versions: France (in French) · Belgium (in French) · Switzerland (in French)

Heating, boilers and hot water

One radiator cold while the others are hot: what to check

Start with the room and its controls, then investigate the radiator.

The answer in 2 lines. If the other radiators are heating but a room remains cold, check that radiator's normal control first. A closed valve, trapped air or a circulation problem could explain the difference. A boiler producing hot tap water is not proof that the central heating is calling for heat. Note the pattern before arranging a repair, and leave pipe connections and technical adjustments alone.

Start with these checks

  1. Compare radiators while the heating is actually running. Note whether the affected room is uncomfortable or has already reached the temperature you want.
  2. Check the programmer, room thermostat and normal radiator control. Turn only the usual handle, gently, following the equipment instructions.
  3. Record whether the radiator is entirely cold, colder at the top or has persistent cold patches lower down. Mention any recent heating work.

Stop: danger

  • A stiff or leaking valve: stop turning it. Do not use pliers to pull a valve pin or loosen the valve body.
  • Hot system water: do not loosen radiator connections or remove a bleed screw. Allow equipment to cool before any maintenance permitted by its instructions.
  • Boiler casing: do not remove it to investigate a radiator fault. Work on gas components requires the appropriate registered competence.

Is the radiator supposed to be heating?

Check whether central heating is enabled, rather than hot water alone, and whether the heating programme is active. A radiator may cool once its room is warm enough, even while another room still needs heat.

Citizens Advice's heating controls guide explains the roles of the timer, thermostat and radiator controls. Use the sections matching your equipment to check your usual settings before reporting a fault. Note the settings you checked so the next person does not have to start again.

What the temperature pattern can tell you

  • Entirely cold: check that the normal radiator valve is open. If the room still needs heat, ask for a local valve and flow check.
  • Cold at the top: trapped air is a possibility. Read the linked bleeding guide below and check your system instructions before proceeding.
  • Persistent lower cold patches: deposits or restricted circulation merit investigation; bleeding is not automatically the answer.
  • Several poorly heated rooms: ask for a wider check of heat distribution.

The council repairs handbook discusses cold radiator tops and continuing faults. Search for “radiator” to find the relevant section; tenants should follow their own landlord's reporting instructions.

What not to do

  • Turning the boiler temperature up repeatedly to compensate for a single radiator that stays cold.
  • Repeatedly bleeding a radiator without establishing whether trapped air is likely.
  • Adjusting the capped lockshield valve without understanding its balancing function.
  • Closing other radiators to force circulation without advice specific to the installation.

What to ask a heating engineer

Explain which radiators heat at the same time and whether the problem followed decorating, radiator replacement or other work. Ask the engineer to distinguish a valve fault, trapped air, poor balancing and deposits. A moving control handle does not establish that water is flowing correctly through the radiator.

The Heating and Hotwater Industry Council's balancing guidance explains why uneven flow, pump problems and sludge can produce overlapping symptoms. Read its discussion of cold radiators to prepare questions about the diagnosis. Ask for the proposed repair and expected result in writing before approving more extensive work.

Reporting the fault in a rented home

Send your landlord a clear written report: the affected room, whether other radiators work, the controls checked and any leak. Ask how the repair will be investigated. GOV.UK's repairs guidance explains the landlord's general responsibility for heating installations and how to pursue repairs; follow its reporting steps if the problem remains unresolved.

With communal heating, report the problem to the building's heating contact using your tenancy or resident information. Ask before manipulating shared equipment. This article covers England; repair procedures and tenancy rules differ in Wales, Scotland and Northern Ireland.

Good to know

  • Bleeding releases air. It does not repair a faulty valve or establish whether the system needs cleaning.
  • A room that remains comfortable matters more than whether its radiator feels hot throughout the day.
  • After a repair, ask for the result to be checked during an actual heating demand, with your normal controls restored.

Illustrative example: Aisha's living room warms up, but the bedroom stays chilly with its radiator cold. She checks the heating programme and gently opens the bedroom's normal radiator control. When nothing changes, she records the contrast between the rooms and requests a valve and circulation check. She leaves the pipe connections and balancing valve untouched.

A made-up story, for illustration.

Bobby

Read more guides

Bobby publishes free practical guides written for England: English laws, numbers and organizations. In England, Bobby answers your questions; it does not put you in touch with professionals.

All guides: England

Sources, verification, confidence

Verified on 7 November 2026, for England. Confidence: high for the initial control checks, possible trapped air and the need to distinguish circulation faults; medium for the cause of an individual cold radiator. Symptoms alone cannot establish which component needs repair.

Related guides

Also worth reading